Search:

Type: Posts; User: AcadDude

Search: Search took 0.12 seconds.

  1. Replies
    2
    Views
    1,441

    Look at the game settings under UI / Streaming....

    Look at the game settings under UI / Streaming. There is a setting called Enter Initials-Classic:. Set that to Enabled and you should see initials set with flippers and launch button.
  2. Replies
    3
    Views
    1,389

    Eye in the sky has little sockets to catch the...

    Eye in the sky has little sockets to catch the ball when you press the flipper. it must hit one of the empty sockets or fails. You have to watch the spinning arms close. The vertical car you have to...
  3. Replies
    0
    Views
    49,294

    Adding a view toggle button

    Just when I thought the cabinet had enough buttons, I had to add a button. Danged ole view change. I started to play a few tournaments on FX3 and the default view wasn't what I wanted. I have all the...
  4. Replies
    3
    Views
    1,962

    Williams Pinball Achievements Accomplished

    Finally got all the Williams Pinball Achievements Accomplished!!!:cool::cool::cool:

    Took me a little bit but I finally maxed out the Achievements for the Williams tables.

    1490
  5. Replies
    11
    Views
    5,069

    Looks good. Should be fun to play!

    Looks good. Should be fun to play!
  6. Replies
    3
    Views
    2,987

    I am using the VirtuaPin in my cabinet

    I am using the VirtuaPin in my cabinet
  7. That PC would do 1k just fine. I don't see the...

    That PC would do 1k just fine. I don't see the need for 4k just yet for virtual pinball. I have done a bartop game with a 32 inch monitor in portrait. I set it up to just use the one monitor and FX...
  8. Replies
    1
    Views
    1,540

    I spent $3000 building one from scratch. Start...

    I spent $3000 building one from scratch. Start pricing the parts and after computer and monitors you get most of the way to 2 grand. Then add buttons and control emulators. Try FX3 on a PC and see if...
  9. Replies
    7
    Views
    3,631

    I cannot remember how many buttons are minimum....

    I cannot remember how many buttons are minimum. I have 6 mapped. Primary Action, Go Back, Tertiary Action, Secondary Action, Left Shoulder, DPAD Left.
    I mapped the plunger to the right analog and...
  10. Replies
    7
    Views
    3,631

    I set mine up as a steam generic controller. I...

    I set mine up as a steam generic controller. I set all the buttons in the steam controller setup.
  11. If you switch out of cabinet mode then you have...

    If you switch out of cabinet mode then you have to reenter the code you were given before to get back to cabinet mode
  12. Replies
    4
    Views
    1,782

    Be sure to check the settings "Backglass...

    Be sure to check the settings "Backglass repositioning" and "Dot matrix repositioning" are set to on. Otherwise it is a math problem to whether or not you have negative or positive values due to...
  13. Replies
    509
    Views
    173,508

    Party Zone I keep getting ball stuck in left...

    Party Zone

    I keep getting ball stuck in left Ozone ramp. It tries to push the ball up and over but stays there through a minute of resets until it finally has enough to get back into play.
  14. Replies
    0
    Views
    4,228

    Pinball Cabinet Home Built

    This is my home built cabinet. Playfield is 4k 49" TV monitor. DMD is 15.6 monitor USB monitor (1366x768). Backglass monitor is 32" monitor (1920X1080)

    This runs FX3 pretty well. This is actually...
Results 1 to 14 of 14